Major in Decorative Wire Mesh, Rope Mesh, Metal Curtain Mesh, Extruder Screen Mesh,Gabions Mesh, panels etc.

 

Mutual trust, Mutual Development And Mutual Profit!

 

Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
Home News

Extruder filter Screen Maintenance Items

Good quality Extruder Screen/Screen Pack for sales
Good quality Extruder Screen/Screen Pack for sales
BM help us lots of deals ,every time they are finished all of the jobs in time,Every Extruder Screen Disc Order Suit our standard.From South Africa

—— Bob

We work with BM Metal Mesh since 2010 years , they have been provding Quality Gabions Basket Materials and excellent sales after service .From Sweden

—— Paul

Good service and quality decoration metallic mesh ,you good option for purchase Decoraive Metal Mesh-From New Zealand

—— Tim

Aviary Mesh/ Parrot Wire Net Delivery time is on time.Quality and service is very good.work together in future- From England

—— Georgia

We works on plastic extrusion we need a high pressure peak at the end of extruder before die. So we use screen filter mesh to keep pressure high,work well

—— Jennifer

I'm Online Chat Now
Company News
Extruder filter Screen Maintenance Items

Extruder filter Screen Maintenance Items

 

With the development of the plastics industry, plastic extruders have become popular in the plastics production industry. Learning how to maintain and how to maintain the plastic extruder is very helpful to our production. Today we are talking about the filter in the extruder, which aspects should be noted in the actual production.


1: Since ordinary wire mesh screens are prone to rust, avoid moisture during storage, otherwise rust will appear in the extrudate. What's more, rusted filters are prone to breakage and allow filtered impurities to leak through, so the filters are stored in plastic bags or rust-proof paper, but now there are alternatives to wire mesh — - Stainless steel filter. (BangMai Metal Mesh Factory specializes in producing various models of stainless steel strainers.)


2: When the PVC material is being extruded, the bare filter must not be placed on the extruder head. This is because the hydrochloric acid in the air near the head mold will corrode it. The best practice when extruding PVC is to install a fume hood above the die, and be sure to keep the backup filter away from it, or even pack it in a freezer.

 

3: When the purge and cleaning of the protection board is very easy to appear rewinding phenomenon, so that the sealing surface is damaged, and the sliding surface does not match, resulting in leakage. This will not only result in time-consuming cleaning, but also leaks of molten material that can affect the thermocouple value, as well as damage the heater, and may even cause a fire.

 

4: For a single-exhaust, two-stage extruder, if the back pressure at the filter becomes larger, then the second stage of production will be reduced, but the output of the first stage will not be affected. When the back pressure increased to approximately 2500 lb/in2 (1 lb = 45536 Kg, 1 in = 25.4 mm), the molten material from the first stage began to leak into the vent. In order to avoid this, it is important to replace the filter when the pressure is low. In addition, the gear pump behind the filter device also inhibits the leakage of molten material into the vent.


5: If the filters filter to large debris (such as paper), it will suddenly fail completely, which will make the extruder pressure quickly peak. Therefore, in order to prevent this from happening, there must be a safety system such as a safety diaphragm, a safety pin, or an alarm connected to a pressure gauge.


Summary: If the extruder filter does the above 5 points, then basically you can do not worry about filters.
 

 

Pub Time : 2013-08-28 17:00:35 >> News list
Contact Details
AnPing BangMai Metal Mesh Product Co.,Ltd

Contact Person: Ms. karen

Tel: 86-159-3230-4587

Fax: 86-318-7523109

Send your inquiry directly to us (0 / 3000)